產品描述

The SN95302FG/SN95303FG is a 16-bit DSP processor with SONiX OID decoder function. It runs at 48MHz with 48MIPS high performance processing speed. SN95302FG/SN95303FG built-in 64KW ROM, 16KW Program RAM and 16KW Working RAM. However, SN95302FG/SN95303FG allows run code at external SPI flash.

Peripherals embedded in the SN95302FG/SN95303FG include OID sensor interface, XtraROM interface, SD/MMC controller, USB device, MSP, SPI master/slave interface, PWM Output, Audio ADC and Stereo DAC, I2S and SAR ADC.

產品特色

1.DSP
 Built-in 16-bit DSP core
 48 MIPS CPU Performance under 48MHz, 1 Clock per 1 Instruction.
 Clock Type:
- 48MHz for system clock
- 32KHz for system clock
 High Speed Clock Source (pumping from 12MHz→48MHz by PLL circuit)
- 12MHz crystal oscillator
 Low Speed Clock Source:
- 32KHz is be generated from 12MHz (The actually is 31250Hz)
 Operation Mode:
- Normal mode (hi-speed clock enable)
- mode (hi-speed clock enable, PLL disable, slow-speed clock disable)
- Watch mode (chip entry power-down mode and wake-up per 0.5/1 sec automatically)
- Power down mode (both hi-speed and low-speed clock disable)
 3for 16-bit Timers, 1 Watch Dog Timer, 1 RTC
- Timers with Individual pre-scalar and auto-reload function
- Event Counter (Combine Timer and Input Pin P0.0~P0.2)
- Watch Dog Timer (WDT) with 0.25/0.5/1/2-sec period
- RTC with 0.5/1 sec period
 Interrupt Sources
- 1 for ADC, 3 for Timers, 1 for RTC, 1 for SPI, 1 for AD, 1 for DA, 1 for I2S, 1 for MSP
- 3 for External (P0.0~P0.2), 1 for USB, 1 for SD Card, 4 for DMA
 32KW Internal Program RAM
 Total 16KW Internal RAM memory configuration for Program and working RAM
- Mode 0: 8KW Program RAM + 8KW Working RAM
- Mode 1: 4KW Program RAM + 12KW Working RAM
- Mode 2: 12KW Program RAM + 4KW Working RAM (default)
- Mode 3: 16KW Working RAM
 Support Barrel Shifter and 1616 to 32-bit multiplier
 DMA provided (USB/XtraROM/SDC/SPI)
2.Peripherals and on-chip resources
 Power Supply: 2.7V ~ 3.6V
 Low voltage detection
 Low power reset
 I/O Pins:
- SN95302FG provides total of 29 I/O pins (P0.0, P0.3, P0.7~ P0.10, P1.0 ~ P1.7, P3.11 ~ P3.15, P4.0 ~ P4.9).
- SN95303FG provides total of 27 I/O pins (P0.0, P0.3, P0.7~ P0.10, P1.0 ~ P1.5, P3.11 ~ P3.15, P4.0 ~ P4.9).
 2xSPI (Serial Peripheral Interface)
- Support 1/2/4 bit mode
- Maximum 48MHz Clock frequency
- Support run program on SPI Flash
 MSP (Only SN95302FG)
- Master/Slave mode
- Support General call address
 PWM Output
- Provide 4 I/O pins capable for output 256 levels PWM pulse.
 16-bit Sigma Delta Stereo DAC + Class AB
- Can drive the L/R Channel Earphone.
- SNR 90dB
 I2S Interfce (Only SN95302FG)
- Master mode
- Supports Left/Right justified format
 16-bit Sigma-Delta ADC with AGC function
- Differental / Single-end Microphone input option
- Build-in Microphone Bias Voltage support
 10-bit SAR ADC
- 4 input channel (AIN0 ~ AIN3)
- Input Range 0V~3.3V(VDDA)
- No missing code : 8 bit
 NAND FLASH controller (just support read function)
 SD/MMC controller
- Supports SD Card1.0/2.0 commands
- Supports 1-bit / 4-bit / SPI mode
 USB 2.0 High Speed device
- Supports Storage and HID Class
- Supports Control/Bulk/Interrupt interface
 OID Interface
- Supports dot pattern format : OID_Code_v2 and OID_Code_v3
- Embedded 16 bit-DSP for sensor control and image pattern recognition
- Light source timing control

Application Notes
- SN95302FG_SN95303FG_Application_Note_V1.02.pdf[台灣載點][深圳載點]
Data Sheet
- SN95302FG_SN95303FG_Spec_V1.01.pdf[台灣載點][深圳載點]
Programming Guides
- SN95302FG_SN95303FG_Programming_Guide_V1.00.pdf[台灣載點][深圳載點]

Application Notes

Data Sheet

Programming Guides